In the solid solution state before leaving the factory, the matrix of austenitic stainless steel strip is single-phase austenitic structure. Austenite belongs to the face centered cubic lattice, which is paramagnetic and exhibits non-magnetic or extremely weak magnetism at the macroscopic level. During cold working deformation processes such as cold rolling, slitting, stamping, bending, and stretc
2026-11-16
Solid solution annealing, commonly referred to as solid solution in the industry, is a continuous heat treatment process for austenitic stainless steel coils (304, 316L, 321, 2205 duplex steel, etc.) after cold rolling; It is not the same as ordinary stress relief annealing. The core is to dissolve chromium carbide at grain boundaries into the austenite matrix at high temperatures, and then quickl
2026-11-09
1. Mechanical properties Beneficial: Martensite is a hard phase, which, when combined with cold work hardening, increases tensile strength, hardness, yield strength, and elasticity. This is also the principle of 301 steel strip using large deformation to make spring plates and clamps.
2026-11-03
The overall goal of stainless steel coil storage control is to stabilize the storage environment, isolate corrosive media, and avoid condensation on the surface of the plate. By relying on environmental control, isolation protection, standardized stacking, and regular inspections, the risk of floating rust caused by chloride ions and water vapor adhesion is reduced, ensuring the surface quality of
2026-10-26
Annealing of stainless steel coils is a heat treatment process that generally changes the internal metallographic structure of the material through controlled heating, insulation, and slow cooling, in order to adjust mechanical properties and release residual internal stresses generated during the rolling process. There are corresponding differences in the effects of different annealing process se
2026-10-19
The green spots generated during the storage and shipping of stainless steel coils are essentially chloride ions brought in by salt spray during shipping, forming a condensed water film between the layers and end faces of the steel coils, damaging the passive film of stainless steel, causing crevice corrosion and pitting corrosion, and generating chlorine containing corrosion products; Once water
2026-10-13
Stainless steel materials have high deformation resistance and obvious work hardening. Thin gauge strips are prone to defects such as medium waves, edge waves, quarter waves, and single-sided waves. Generally, roller system mechanical adjustment, segmented cooling, tension control, roller profile pre configuration, online plate shape closed-loop detection, and subsequent leveling and straightening
2026-10-08
1. Nitric acid immersion passivation (traditional chemical passivation) Soak the stainless steel strip in nitric acid bath to remove surface free iron impurities and promote chromium oxidation to form a dense passivation film. Can be divided into multiple concentration levels, suitable for austenitic stainless steels such as 304 and 316; The disadvantage is the generation of nitrogen oxide
2026-09-28
Stainless steel relies on the passivation film of chromium on the surface to prevent corrosion; Chloride ions can penetrate the passivation film, preventing widespread uniform rusting and making it more prone to pitting and crevice corrosion. Under high temperature and tensile stress conditions, austenitic steel may also experience stress corrosion cracking.
2026-09-21
Stainless steel strip protective film (mainly PE protective film) is used to protect the surface of the board during storage, cutting, bending, and stamping processes, preventing scratches, indentations, and dust pollution. The selection of the film coating needs to match the surface type, processing technology, service environment, and peeling time of the stainless steel, referring to GB/T 20878
2026-09-14In the solid solution state before leaving the factory, the matrix of austenitic stainless steel strip is single-phase austenitic structure. Austenite belongs to the face centered cubic lattice, which is paramagnetic and exhibits non-magnetic or extremely weak magnetism at the macroscopic level. During cold working deformation processes such as cold rolling, slitting, stamping, bending, and stretc
Solid solution annealing, commonly referred to as solid solution in the industry, is a continuous heat treatment process for austenitic stainless steel coils (304, 316L, 321, 2205 duplex steel, etc.) after cold rolling; It is not the same as ordinary stress relief annealing. The core is to dissolve chromium carbide at grain boundaries into the austenite matrix at high temperatures, and then quickl
1. Mechanical properties Beneficial: Martensite is a hard phase, which, when combined with cold work hardening, increases tensile strength, hardness, yield strength, and elasticity. This is also the principle of 301 steel strip using large deformation to make spring plates and clamps.
The overall goal of stainless steel coil storage control is to stabilize the storage environment, isolate corrosive media, and avoid condensation on the surface of the plate. By relying on environmental control, isolation protection, standardized stacking, and regular inspections, the risk of floating rust caused by chloride ions and water vapor adhesion is reduced, ensuring the surface quality of
Annealing of stainless steel coils is a heat treatment process that generally changes the internal metallographic structure of the material through controlled heating, insulation, and slow cooling, in order to adjust mechanical properties and release residual internal stresses generated during the rolling process. There are corresponding differences in the effects of different annealing process se
WeChat ID:jinjiayi0512