Flattening, also known as smoothing, is a small reduction rate rolling process after cold rolling and annealing. The reduction rate is usually only 0.5-3%, without changing the material thickness specifications. It relies on the rolling mill to lightly press the surface of the steel strip, and its main functions are as follows:
2026-09-08
1、 At the material level (source priority) 1. Reasonably reduce the hardness of materials For the same grade, the lower the hardness, the higher the elongation, and the smaller the rebound. Example: The original rebound of 301-3/4H was too large. If conditions permit, it can be changed to 301-1/2H, and the rebound will significantly decrease; The cost is a decrease in elasticity, an
2026-09-01
Stamping hardware is the use of punching machines to punch, bend, and stretch sheet metal. Stainless steel coils are used as raw materials for coil materials, taking into account material properties, coil processing advantages, corrosion resistance, appearance, and mass production. They are widely used in various stamping hardware parts.
2026-08-24
Core storage risks of stainless steel strips: iron ion contamination, rust, moisture pitting, surface scratches, coil deformation, mixed material errors, label loss. Once rust spots appear on austenitic stainless steel, they are difficult to remove.
2026-08-17
Fundamental problem: Iron ion pollution (free iron pollution) causes induced corrosion on the surface of stainless steel, rather than the corrosion resistance failure of the stainless steel material itself.
2026-08-10
Stainless steel hot-rolled surface is not suitable for directly producing exposed finished products. Its advantages are thick thickness, low cost, and high substrate strength, making it suitable for working conditions that require subsequent cutting, forming, and precision machining.
2026-08-03
Divided into two categories: hot-rolled stainless steel coils and cold-rolled stainless steel coils (2B/BA, etc.) The mainstream route of steel mills: electric arc furnace smelting → AOD refining → continuous casting billet → hot rolling (producing hot-rolled coils); Hot rolled coils are used as raw materials and then enter the cold rolling process to produce cold-rolled stainless steel coi
2026-07-28
Classify and organize according to new energy, traditional electricity, oil and gas petrochemicals, hydrogen energy, and nuclear power, and distinguish three types of uses: ultra-thin precision steel strips, structural bundling steel strips, and heat-resistant conveyor steel strips:
2026-07-22
Stainless steel has high deformation resistance, is prone to work hardening, is easily oxidized at high temperatures, and is prone to cracking at the edges. It is divided into two parts: hot-rolled billet rolling and cold-rolled precision rolling. The raw materials, temperature, process parameters, equipment, lubrication, plate shape tension, surface protection, and later microstructure and proper
2026-07-13
Hot rolled stainless steel coil is a thick material coil produced by high-temperature rolling, with a thickness range of 1.5-16mm and a surface with oxide black skin. It is thick in size, high in strength, and does not require appearance. It is mainly used in structural pressure bearing, chemical equipment, and heavy machinery scenarios.
2026-07-07In the solid solution state before leaving the factory, the matrix of austenitic stainless steel strip is single-phase austenitic structure. Austenite belongs to the face centered cubic lattice, which is paramagnetic and exhibits non-magnetic or extremely weak magnetism at the macroscopic level. During cold working deformation processes such as cold rolling, slitting, stamping, bending, and stretc
Solid solution annealing, commonly referred to as solid solution in the industry, is a continuous heat treatment process for austenitic stainless steel coils (304, 316L, 321, 2205 duplex steel, etc.) after cold rolling; It is not the same as ordinary stress relief annealing. The core is to dissolve chromium carbide at grain boundaries into the austenite matrix at high temperatures, and then quickl
1. Mechanical properties Beneficial: Martensite is a hard phase, which, when combined with cold work hardening, increases tensile strength, hardness, yield strength, and elasticity. This is also the principle of 301 steel strip using large deformation to make spring plates and clamps.
The overall goal of stainless steel coil storage control is to stabilize the storage environment, isolate corrosive media, and avoid condensation on the surface of the plate. By relying on environmental control, isolation protection, standardized stacking, and regular inspections, the risk of floating rust caused by chloride ions and water vapor adhesion is reduced, ensuring the surface quality of
Annealing of stainless steel coils is a heat treatment process that generally changes the internal metallographic structure of the material through controlled heating, insulation, and slow cooling, in order to adjust mechanical properties and release residual internal stresses generated during the rolling process. There are corresponding differences in the effects of different annealing process se
WeChat ID:jinjiayi0512