1、 Core material foundation: 304/316L itself is austenitic non-magnetic stainless steel 304 and 316L belong to austenitic stainless steel. In the factory solution annealed state, all internal crystals are austenitic structure, and the austenitic crystal structure does not have ferromagnetism. The new soft steel strip is almost non-magnetic, and the magnet does not adsorb.
2026-06-30
1、 Open coil basic processing (the first process of coil material) 1. Kaiping/Splitting Kaiping: Stainless steel coils are uncoiled, leveled, and cut into flat plates (stainless steel plates) for cutting, bending, and laser cutting. Slitting: Large rolls are cut into narrow strips of steel for welding pipes, steel strips, precision stamping, strapping, and decorative edge strips.
2026-06-22
1、 Key points of pre-treatment before passivation 1. The surface must be degreased and cleaned Rolling lubricating oil, stretching oil, rust proof oil, fingerprints, and dust will isolate the passivation solution, causing uneven thickness of the passivation film, partial failure to apply the film, and non-compliance with salt spray standards. Light and thin steel strip with priority alkal
2026-06-15
1、 Mainstream surface of cold-rolled stainless steel coil (most commonly used in the market) 1.2B surface (large amount, basic universal surface) Cold rolling → annealing and pickling → mild flattening of the finishing roll, presenting a matte silver gray color with a delicate and non reflective feel.
2026-06-09
1、 Austenitic stainless steel strip (mainstream grades 301, 304, 316L) Referring to HV Vickers hardness and HRB Rockwell B, industry standard states: soft, 1/4H, 1/2H, 3/4H, H, EH, SH
2026-06-01
The high utilization rate of stainless steel coils is mainly reflected in flexible cutting, low loss, adaptability to continuous processing, and strong specification adaptability. Combined with actual production scenarios, it is explained that:
2026-05-26
The core of stainless steel strip preservation is constant temperature, low humidity, cleanliness, isolation, and protection from light and rain to prevent damage and corrosion of the passivation film.
2026-05-18
1、 Common surface types 2B, BA mirror, brushed, frosted, 8K mirror, polished surface, hot-rolled surface 2、 Impact on core performance 1. Corrosion resistance Mirror/polished/BA surface: The surface is smooth and dense, without scratches or gaps, has good corrosion resistance, and is not easy to accumulate dirt or rust. 2B matte surface: medium corrosion resistance, industri
2026-05-11
The core of selecting stainless steel coils is to first determine the material according to the corrosive environment, then determine the specifications and surface according to the processing/stress, balance the cost and service life, and verify the quality assurance and dimensional accuracy of the steel mill.
2026-05-07
1、 Overall Overview Stainless steel strip is produced using precision cold rolling, continuous rolling, high-precision roller system, and closed-loop thickness control system, combined with annealing leveling and precision slitting processes. The overall thickness tolerance is small, the width is correct, the flatness is high, the edges are regular, and the uniformity of the same roll is st
2026-04-27In the solid solution state before leaving the factory, the matrix of austenitic stainless steel strip is single-phase austenitic structure. Austenite belongs to the face centered cubic lattice, which is paramagnetic and exhibits non-magnetic or extremely weak magnetism at the macroscopic level. During cold working deformation processes such as cold rolling, slitting, stamping, bending, and stretc
Solid solution annealing, commonly referred to as solid solution in the industry, is a continuous heat treatment process for austenitic stainless steel coils (304, 316L, 321, 2205 duplex steel, etc.) after cold rolling; It is not the same as ordinary stress relief annealing. The core is to dissolve chromium carbide at grain boundaries into the austenite matrix at high temperatures, and then quickl
1. Mechanical properties Beneficial: Martensite is a hard phase, which, when combined with cold work hardening, increases tensile strength, hardness, yield strength, and elasticity. This is also the principle of 301 steel strip using large deformation to make spring plates and clamps.
The overall goal of stainless steel coil storage control is to stabilize the storage environment, isolate corrosive media, and avoid condensation on the surface of the plate. By relying on environmental control, isolation protection, standardized stacking, and regular inspections, the risk of floating rust caused by chloride ions and water vapor adhesion is reduced, ensuring the surface quality of
Annealing of stainless steel coils is a heat treatment process that generally changes the internal metallographic structure of the material through controlled heating, insulation, and slow cooling, in order to adjust mechanical properties and release residual internal stresses generated during the rolling process. There are corresponding differences in the effects of different annealing process se
WeChat ID:jinjiayi0512